Keymaps for several of my boards (#1641)

* copied mjt keymaps from archive

* All mjt boards now compile

* fixed jd45-mjt breathing

* Updates to fix SpaceFN but not tested yet.

* Still missing either spacebar or an adjacent keypress.

* Debugging rigged up for use with hid_listen.

* Reverted the default keymap to use tap_layer_key rather than custom.  Moved custom approach to keymap_debug.c

* Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function.

* Cleaned up JD45 keymap that uses tapkey.

* Redid minivan keymap with numsym rather than raise/lower.
Untested.

* Created my MJT keymap for HHKB
Enabled dynamic macros and moved
somoe of the shortcuts around.

* Minor keymap fixes to make them compile without errors.

* Added home/end to right arrow cluster on DYN layer.

* Added more keys to fn and dyn layers.

* It wasn't using my custom layer last time somehow...?  Now it will.

* Compiled and installed at end of day on 8/23

* Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback.

* Fixed volume controls... were reversed and disabled.

* Added F13-F15 back to fkeys layer in Minivan

* Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan.

* Removed DYN layer.

* Fixed diagram in planck numsym.

* Cleanup for pull request.

* Roadkit flip phone warning.

* Replaced PLAY_NOTES_ARRAY to PLAY_SONG

* reset the submodules

* checked out specific commits for submodules

* Removed debugging from JD45 shared config.h

* Moved custom rules.mk to apropriate keymap

Reset the shared rules.mk file.

* Trailing return issue in rules.mk

Gotta make for a smooth pull request :-)

keyboards/jd45/keymaps/mjt/rules.mk

@@ -0,0 +1,67 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
+NKRO_ENABLE = yes		# USB Nkey Rollover - not yet supported in LUFA
+BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
+MIDI_ENABLE = no 		# MIDI controls
+# UNICODE_ENABLE = YES 		# Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID